Target Grade .22 Single Six: New unfluted 6 shot cylinder is made and fitted to frame. Cylinders feature match grade chambers with proper throat size and linebored for accuracy. Oversize base pin, action job and new barrel standard. Factory front sight remounted. Blue or SS $1595
Add $450 for extra cylinder in .22 Magnum
Misc. services for NM and OM Single Six .22 & .32
Shorten factory barrel and remount sight- $125 Add $50 for barrel lengths under 4 5/8". Add $25 for fixed sight models
Action job- $185
Scallop recoil shield- $125
Bowen Rear sight- Target $125 Rough Country $110
Belt Mountain oversize base pin with no lock screw- $50
Rebarreling- from $350
Cyl. endshake repair- $60
Blackpowder chamfer cut on fluted cyl.- $70
Custom fixed blade patridge style front sight- $75
Barrel/cyl. gap set- $125
Recut chambers or throats as needed- $65
Sight regulation for fixed sight guns- $50
Basic Accuracy Tuneup package for .22 Single Six NM & OM- After doing many of these in the past, I have come up with a list of services that will cover most guns and make them the best they can be.
Action job with 3-3 1/2# crisp, creep free pull (OM guns are set to 2 1/2-3# pull), throat barrel, recrown muzzle, check cyl. throats and chambers and recut as needed- $300
Tuneup package for Single 9 & 10 to above specs- $350
Your gun will be checked out thoroughly and I will notify you of any other issues that might need attention.
NM Single Six .32
.327 Federal- I am currently offering custom cyls. in this caliber since the factory cyl. is too short for the cartridge. These will run $650 for the cyl. only fitted, linebored, and chambered to your gun. Shortening of barrel at rear and recutting forcing cone is done also. Cyls. will be of the open casehead design. Options from above can be added.
Basic Tuneup package for .32 Single Six or Single 7- Action job with 3-3 1/2# trigger pull, crown and forcing cone recut or polished as needed. The factory loading problem on the single 7 will be fixed as part of this package. $225
Options from above can be added to either Tuneup package.
You can send in your gun for the basic tuneup packages at anytime. 30-45 day turnaround.
6 shot conversion to .38 Special and/or 9mm based on the Ruger Single 6 frame. Available on blue or stainless guns.
The guns are a pleasure to shoot even with hot handloaded 180 gr. bullets. Accuracy is superb in .38 and 9mm with several different loads and bullet weights.
Loading recommendations: Standard factory loads in 9mm Luger. .38 Special standard or +P factory loads.
.38 handloads: 125 gr. bullet to 1200+ fps, 158 gr. to 1150+, 180 gr. to 1100+. Load data furnished with each gun. Cyl. will take an overall cartridge length of 1.5".
Suitable base guns: Ruger Single 7 .327 or any Single 6 in .32 cal.
At this time I will not take any rimfire Single 6's for conversion or consider any calibers other than .38 Special or 9mm Luger.
6 shot open casehead, unfluted oversize cyl. fitted to frame. Throats and chambers linebored.
Power Custom free spin pawl
New custom barrel or repurposed factory barrel with rounded style crown
Action job with 3# trigger
Action internally blocked to tighten
Rework loading port
Remove and remark caliber designation
Scaled to fit pinned blade front sight with patridge blade or dovetail blade on fixed sight guns
Refinish complete: Stainless-beadblasted or brushed. Blue- polish blued.
Conversion with custom barrel in your choice of length: $1850
Conversion with repurposed factory barrel @ 4 5/8": $1750 check for availability
Auxiliary cyl. in 9mm: $650
Bisley hammer: $100 check for availability
Belt Mtn. oversize base pin: $50 Colt, standard, or #5 head
Recessed casehead cyl.: $100
Cresent head ejector rod: $15
Other style front sight blades: inquire
Options shown on gun below: Custom walnut grips, Belt Mtn. oversize base pin with Colt style head, Bisley hammer, cresent head ejector rod, custom rear sight, and recessed casehead cyls. Base gun was a Single 7 .327.
Pictured below is full custom Single 6 Vaquero in .22 LR. Features include, custom fluted and blackpowder chamfered 6 shot cyl., Bisley hammer, 4 5/8" match barrel with dovetail front sight, cresent head ejector rod, Belt Mtn. Colt style head base pin, scalloped recoil shield, desert bighorn sheep grips, light matte beadblast finish.