Clements Custom Guns

Home

Ordering and Payment Info

Marlin Rifles- Tuneup

Marlin Services

Ruger SA Packages

SA Revolver Services

Single Six


   
                        
Ruger Single Action Revolvers

                               


Tune-up package for all Ruger SA centerfire revolvers:  Action job with 3-3 1/4# trigger pull, oversize #5 base pin with lock screw, polish or recut forcing cone and barrel crown, open cyl. throats for cast bullets, alignment check, correct timing as needed, and custom pinned blade front sight base with choice of any blade from below.- $850 SS or blue- dual cylinder guns add $100

Bowen rear sight- $110-$130

To shorten barrel on tune-up package add $200

Set barrel/cyl. gap to minimum on tune-up package add $150

Correct cyl. endshake add $75

Matte beadblast stainless gun $100

Add colorcased frame, loading gate, & hammer for blued guns to any tuneup package for $425. 

Caliber Conversions

Calibers available:

Large frame New Model Blackhawks and Older Vaqueros:  .44 Special    .38-40  10mm  40 S&W   .41 Magnum  .45 ACP  .45 Colt  .44 Magnum  .44-40

New Vaqueros in .357, Flat Tops, and 3 Screws with .357 size frames:  .44 Special  10mm  40 S&W   .41 Special  .41 Magnum   .45 Colt (light loads only)  .45 ACP   .38-40  .44-40

6 shot caliber conversion- Conversion utilizes a new custom barrel in your choice of length to 7.5" with straight or tapered contour and factory cylinder. Forcing cone cut to 11 degrees and barrel fitted to minimum barrel/cyl. gap. Cylinder is linebored and rechambered. Action job. No. 5 base pin. Custom pinned blade front sight base with your choice of any blade from below. Old caliber designation will be removed and gun properly remarked. Select caliber from above according to frame size of base gun. Contact me if you need help with this. Base gun must be at least 1 caliber smaller than conversion caliber. 

Blue gun- $1595

Stainless gun- $1595

Blue gun with Turnbull colorcased frame, loading gate, & hammer- $1995

Finish options for conversions:

Standard factory equivalent polish- included

High polish blue- add $50

Factory equivalent brushed stainless polish- included

Matte beadblast finish on stainless gun- included

Refinish alloy gripframe- $85

Conversion options:

Install bushing in ratchet end of cylinder $75

Cut Blackpowder chamfer on fluted cylinder $85

Correct cyl. endshake as needed $75

Tighten rotational slack in cylinder by blocking cylinder latch and trigger on NM guns only $250

Steel ejector hsg. $65

Cresent ejector rods for round barrels only- blue or SS $15

Scollop recoil shield $175

Gripframe installation- RW frames only POR

Bowen rear sight $110-$130

Linebore and chamber customer supplied auxillary cyl. From $375

Install stainless Bisley hammer on guns with standard gripframe $95  NM guns only

Install stainless Super Blackhawk hammer on guns with standard gripframe $50  NM guns only

The following sight blades are available for pinned bases. All blades are approx. .120" wide. Add $10 for widths thinner than .120". 

Standard black serrated patridge style with 30 degree forward tilt on sight face

Patridge syle with brass bead 

Post front sight 

Post front sight with brass bead 

Fiber optic in red, yellow, or green 

Keith style plain black 

Keith style with brass bead 

Black serrated ramped  

Patridge style with vertical white line 

Patridge style with 1-3 gold bars depending on height. The bars are intended as sighting reference points only.


.44 Special conversion. Shown with optional steel ejector hsg., blackpowder chamfered cyl., Bowen rear sight, and pinned blade front sight.