Scallop recoil shield on any Ruger SA revolver- $125 This service offers a slight weight reduction while affording a unique look to gun. I EDM cut the scallops so there is no change of damage from a slipped file. Only very light polishing is required to finish the job. Receiver and loading gate will need to be reblued afterwards. This service is only available on conversions and package guns.
Cut blue or SS SA barrel and remount factory front sight $225. Cut blue SA barrel and mount custom fixed blade front sight $285. Cut blue or stainless SA barrel and install custom pinned blade front sight $350. Add $10 if HD style sight is wanted. Services include bluing of barrel only. For shortening barrels to less than 4 5/8" add $50.
Remove barrel label on barrels cut to 5" or less $50 Only applicable with barrel shortening.
Vaquero: shorten barrel and install windage adjustable dovetailed front sight $275 Extra charge for shortening a 5 1/2" barrel to 4 5/8" $25
Vaquero: shorten barrel and remount factory sight blade- $225 Extra charge for shortening 5 1/2" barrel to 4 5/8" $25
Vaquero: install windage adjustable dovetailed front sight $165.
Pinned blade conversion of factory front sight base on blued guns with patridge style blade $150 Other blade styles on request- see #18. I can make about any style you can dream up- inquire.
Install patridge style blade on stainless factory barrel $65
Install custom front sight with patridge style black pinned blade on factory barrel $200 For HD style front sight add $10
Install custom fixed blade sight on factory barrel $140.
Extra sight blades with custom sight work from $50 each. Individual blades are available from $50 for customer installation to fit Ruger factory stainless pinned bases and Freedom Arms guns- inquire
Add horizontal gold bars to sight blades $15 per bar Add vertical whiteline $15 Add gold bead $25 Blade with fiber optic insert add $30 green, yellow, or red
Bowen rear sight - Target style $125 - Rough Country $110 (note: the Rough Country sight must have the adjustment screws loctited after setting to keep them in place. They are only available to fit the OM Flattop and NM Blackhawk guns.)
Action job for all Ruger Single Actions $200: 2.5-3# pull on OM guns, 3-3 1/2# trigger pull on NM guns- Internal parts are polished and sear surfaces are carefully ground to produce a clean, creep free trigger pull and then rehardened on NM blue guns to maximize life. Add reduced power mainspring for $10 to ease cocking effort.
Install new factory pawl to correct timing $60 when done with trigger job or conversion $30
Freewheel New Model SA cylinder $25 when done with action job, $40 if preformed by itself. Centerfire guns only
Blue steel ejector housing $65 Target length ejector assy. $85 Customer supplied ejector housings that are not Ruger brand will be returned unused due to poor fit and quality. Guns that have a stud on barrel add $20.
Bowen oversized base pin with lock screw $70 (knurled head)
Install Belt Mtn.#5 base pin with lock screw- $65 Non locking Belt Mtn. pins- $50
Colt style black powder chamfer cut on fluted cylinder $70
Flute custom cyl. or reflute factory cyl. wider and deeper $150
Furnish and fit Bisley hammer to Blackhawk $85 NM guns only Availability is limited.
Correct cylinder endshake - SA $70
Set barrel/cylinder gap $125
Jewel hammer or trigger $20 each
Round butt SA grip frame and recontour grips - $100 stainless $125 blue When added to conversion, cost is $95 for either blue or stainless.
Recut forcing come to 11 degrees- from $25
Recrown muzzle- from $25
Open cylinder throats for cast bullets $75
Engrave customer's name or initials on gun $50 (all block letters on barrel, butt, topstrap, or side of receiver)
Engraving in script letters - This type of engraving is available for $50 per line with a $25 programming fee applicable to first gun. We save these CNC programs and do the same engraving on another gun for $45. All engraving is CNC mill cut.
Install blue or stainless lanyard ring- $85
All custom cylinders are made inhouse from 17-4 stainless and 4140 CM to fit each individual frame, as no two are the same. Unless noted, all are of the recessed casehead design unless the customer specifies differently. They are linebored through the frame to insure proper bullet/barrel alignment. Cylinder throats are properly sized for best performance with cast bullets.
Clements Custom Guns 2766 Mt. Zion Rd. Woodlawn, VA 24381